12 Square Meter Cotton Tent Affairs Disaster Emergency Refugee Relief Tent

One. Main function
Mainly used for resettlement of victims in plain areas. It can accommodate about 5 people temporarily.
Second, the main performance introduction
(1). The tent is in the form of a double-slope vertical wall. The frame is a plug-in structure with floor rails. It can be used safely under its own weight and 8-level wind. See Figure 1 for an overview of the unfolded state. Bracket structure schematic
See
Figure Below 

Figure 1: Diagram of the unfolded state of the 10.24m2 disaster relief single tent
          1-Universal rod   2-Gable pole   3- Frame connector   4-Middle frame connector   5-Ground Pole Connector    6-Pole    7-Wire rope
Figure 2: Schematic diagram of the 12m2 disaster relief single tent support structure

(2). The tent is 3.2m long, 3.2m wide, 2.2m high and 1.6m high. The usable area is 10.24m2.
(3). The tent surface cloth is coated with 300DPVC coated cloth on one side, which has the properties of tensile strength, tear resistance, aging resistance and rain resistance. Under normal circumstances, it can be used continuously for more than 2 years.
(4). The tent has a simple structure and is easy to set up and remove. 15min/6 people can complete the erection.
Two. Classification and packaging of tent parts

After all the parts of each tent are classified and packaged, there are 2 pieces in total. Please refer to the packing list for details
Three Erection
1. Open the single canopy packaging bag and the frame packaging bag, take out the product packaging list and count the quantity of each part.
2. Take 8 universal rods and three groups of end frame tee and middle frame tee that have been pressed and fixed with steel wire rope to form three groups of herringbone frames connected and connected.
3. Take 4 universal rods, end frame tee and middle frame tee to form a frame.
4. Place the canopy on the three sets of herringbone frames and adjust the position.
5. Take 6 vertical poles and insert them into the end frame tee and the middle frame spool respectively, and use 6 people to support the canopy at the same time, and connect it with the ground poles that have been placed.
6. Tighten the straps at all parts, fasten the nylon zippers, and adjust the tent position to connect with the rods of the frame.
7. Drive the triangle pile in the corresponding position on the ground, fix the rope, adjust the tightness, and put the rubber-plastic pile head cover on the end face of the triangle pile.
8. Tidy up the tent and bury it with soil around the tent.
Four. Withdrawal
1. The retraction process of the tent is opposite to that of erection. When retracting, refer to the erection method and steps in reverse order.
2. When folding a single canopy body, fold it according to the size of the canopy body packaging bag and put it into the packaging bag.
3. After checking the tent poles and parts according to the packing list, put them into the tent pole packaging bag in turn.

Five. Precautions for use and maintenance
1. When erecting and retracting, do not drag the single canopy on the ground to avoid soiling and tearing, causing unnecessary damage.
2. During use, pay attention to keep the inner and outer tarpaulin clean.
3. After rain, snow and strong wind, check the top of the tent and the surrounding ground for water, snow and loose ropes, etc., and clean and adjust it in time to ensure that the tent is in normal use.
4. The wet tent is not allowed to be stored for a long time. It must be aired and dried in time before packing and storage.
5. The tent parts shall not be used for other purposes.
6. The packaging bag of the tent should be properly stored with the tent and must not be lost for recycling.
7. During the use of the tent, if any damaged parts are found, they should be replaced in time.

Q1: Are you manufacturer?
A: Yes, we are a company which major in producing kinds of tactical uniforms and outdoor camouflage clothing.

Q2: Whom is your main clients?
A: Out main buyers are for goverment tenders, Airlines, UN, etc. Our main markets are in Europe, Middle east and african countries.

Q3: Is OEM or ODM OK to your company ?
A: Yes. We can make samples according to your design.OEM and ODM are welcome.We have the exclusive right in exporting tactical suppliers.

Q4: When is your convenient time for buyer to contact?
A: We have online replying services for 24 hour, so we will respond any time at client's convenience.

Q5: If I want sample, what can I do?
A:Pls contact us, we will send details for your selection. Original sample can be remade, but buyers have to pay for the FREIGHT BILL.

Q6: How about your products'quality?
A: Fronter already approved ISO and SGS certificates, our partners dyeing factory is the Top 3 in China. The third party inspection is also acceptable to us.

Q7: Can I get a discount for the order?
A: Of course, the price depends on your order quantity, we will offer you the best price and give you a discount if you order large quantity.